老爺同老電都未完, 咁快又起老溫~ 遲少少先啦~ 一係就SET TARGET DATE 長D

開到09尾........ arm晒我d手慢人~~

咁就快d啦~~
我可以慢慢睇住做啦~~

諗左一大輪,覺得係冇可能分開個seat位上色~~~
細佬決定賭一鋪~~~~
將個殼底cut開佢~~
由於自己未試過呢項技術,極有total loss 既可能~~~
大家祝我好運啦

真係唔攪訓唔著~~~
買左套pe鋸幾個月,第一次用真係有d緊張
手術都叫做成功左一半啦~~
聽日要諗諗上完色要點痴返佢~我估要用到膠板~
都係聽日先諗~~~

Let you go first

I need to finish the RA272 first...

Hope you all success!!!

pe鋸/電動打磨機有冇好介紹? Thanks!

真係唔知幫唔幫到你~~~
pe鋸我買左幾個月都係第一次用~都算做幾好鋸既~~
長谷川囉,,平平地,有直有灣,唔知耐唔耐用就真~~~
電動打磨機我就買支(65)鴨記平野,唔算好大力~~,但係鑽首版都叫夠力,搖擺度都唔多,
來仲真係可以駁火牛添~~我前幾日見有d五金鋪係拮牛用ga~~我暫時覺得都算好用~~

冇reference,車形唔識分靚唔靚~~
細既無縫我覺得已經做得幾靚啦~~~
[attach]247112[/attach]
[attach]247113[/attach]
[attach]247114[/attach]
但係以下幅相我遇到既問題係~~~
打磨我覺得盡左力,但係有好多地方都磨唔到~~~
到左將來拋光o個時,我估一係磨穿,一係磨唔到
大家有冇咩方法呀????
[attach]247115[/attach]
[attach]247116[/attach]

Oh I see, I need these too, try to find at Ap liu st...

Thanks anyway!

Waiting to your update process!

How about the "3M" sponge? It seems good for this item...

經過上次刻線唔夠深既經驗,今次請左八襾金上身~~~唔留手~~~
大力d,深d,闊d~~~~~~大多灣位,手工又差,有d"岩參"
見有d接駁位落差幾多,終於恨心試用ab筆地補,睇下呢d貌似blu-tack既物體有幾神奇,又係買左幾個月第一次用~~(而家一手都係)
踏上我改裝既第2步(第一次係鋸野)

[ 本帖最後由 johnnykut 於 2008-11-29 02:54 AM 編輯 ]

3m磨綿我都有用到ga~~
就係磨左好耐都磨剩呢d位~~
我擔心既係第日拋光o個時照我今次咁磨法唔穿真係有鬼囉~~

試下問一個可能已知答案既問題~~~
呢d白殼車,磨完~噴灰check~未得~再執~又噴灰check~~已經五六次~
白殼車係唔係就係咁麻煩????
雖然我估都冇其他辦法,但係都想問一次~

I dont know wor, but it's not the 麻煩...the most 麻煩 is clear clow! My FW24 was that...

其實我估唔係白殼既問題... 而係f1既問題...
星星既f1, 車身組件比較多, 自然縮膠, 夾口都比較嚴重... 我自己之前oob架f310b, 都搞左成兩個星期先上底色(淨計開工日).....

p.s. ab不地用果陣keep住對手濕佢就冇咁痴架啦... 不過用完之後對手仍然都係好似用汽水洗完手咁既......

[ 本帖最後由 lailo 於 2008-11-29 11:44 PM 編輯 ]

都係o個句:白色殼,以為自己磨好,噴完灰先發覺差少少~~又要再磨
下次我估最起碼都要打住燈去做,可能會返手冇咁多掛~~~~
下次磨完應該可以等上色啦~~~~~

開始整定風翼,學人set銅支,(企位穿窿冇得遮添 )
但係學到個形學唔到個神,仲有少少唔對稱
礙於自己技術所限,真係覺得冇得救了
唯有加把勁整埋其他翼~~但係真係好多

其實... 咩色膠都有呢一個問題架.....

你下次砌架花奶f1試下~

都好喎~~~
D線條好似直身D咁~~
但係砌多幾部車先諗LU~~~