第一次砌首辨, 搵隻大大件, 件又唔太多既 1/60 Gouf Custom 試吓. 但因為趕時間,  好多地方都做得唔好. 今次過程 make 左好多 mistake, 都學左好多. 希望下次會好d 啦.
製作過程 post
http://www.hkml.net/Discuz/viewt ... p;extra=#pid1223433

今次只係影左幾張相, 遲d有時間再影.

老友，你好高喎 (Special thanks to SCM EX Zaku)


1/60 Gouf and MG Zaku 1.0











[ 本帖最後由 trex8 於 2008-10-6 11:29 AM 編輯 ]

Thank you! Yes, it is a full kit. It is quite big and heavy, especially the gun/shield. I was afraid the glue is not strong enough to hold it in place.  I used 5 min epoxy. It is supposed to be stronger and won't crack like AA glue. But it really take 24 hours to set complete. I only waited 15 min for the gun/shield. Hope it won't drop some day.

Thanks. 有銅枝. 冇一定頂唔住


Thanks. 其實係老餅懶. 咁多年都唔砌係因為:
1. 懶, 怕打磨
2. 懶, 最憎Masking
3. 未試過set件. 呢隻其實好好set. 反而呢隻人形仲難set. 好多方地要執. 所以爛尾...




Thanks, but nothing compare to Akira big brother la.  衰左好多次, 噴過又噴

Thank you big brother Cody and CKT. It looks good because I did not take any close up pictures yet.
I did a poor job on the backpack 動力管. Wish I have time to repaint it.

Thank you big brother William. 呢隻 good, buy la buy la.


d大水貼上完後刮花 再用筆上小小白油. 之後再稀主色薄薄噴一次. 可惜 "07"個水貼有小小 "silvering"



Thanks! The SCM EX 渣 超可動超正! 好好玩!


呢隻 proportion is very good! I wish it has more details though. I only added a few panel lines.


Thanks! 請問你個頭像係咪自己畫? Looks good wor.


Thanks! SCM EX 渣 roughly 4.75" which is almost 1/144. Bigger and better than EMIA.


因為比較大隻, 自己覺得可以重手小小. Really a personal taste.


Thanks!


陰影方面我唔用 Max噴法.  因為懶,加上缺少資源 (2年多冇返 HK 入貨. 買Mr Color paint 要 mail order) Max 要噴黑底, 用好多油. 我用 preshade. 第一次用紫色結果唔係太明顯。 第二次用藍色 much better


然后用主色加白噴高光位。


以後用主色加小小藍噴轉折位令陰影更自然。 最後用藍色和淺灰色做乾掃增加轉角位層次.



[ 本帖最後由 trex8 於 2008-10-7 11:22 AM 編輯 ]

Without the big feet, it will probably fall...





Thank you. I spent a lot of time fixing (repainting) the mistakes I made. Hope I will do better next time.


Thanks. I need to learn from 千影 how to do 舊化.