Hi everyone

After making of the F430 spider, I have started a new project on the F430 stradale concept. Basically, it would be based on the Fujimi F430 chalenge kit and the 360 stradale decal.


After spraying primer, I have test-built the kit. This kit is different from the hard-roof version which incorporated with engine hood marking on the body and different detail at the tail.

The fitting of this kit is good!

As usual, sanding away the moulding lines on the body.


and primer the body in pink.

Since I have made Ferraris models in black colour before, I would choose the red colour for the F430 stradale concept this time. The red is of Lummi Red by Finisher's paint.

Time to decaling the Italian strips on the body

Done !!!

After allowing to dry the body for 2 days, I have sprayed 2 layers of clear coat on it.

After drying for 4 days, I have sanding the body to level the thickness of the clear coat on the decal and do the compound job as well.


For the cockpit, I have only detailing the steering wheel.

and adding PE for the pedals as well. The interior was sprayed using texture paint.


For the body, the window frames and the windscreen were paints. For the side window, I finally decided to cut them off and allow them to remain open for better viewing the cockpit.


Up to now, only some more details to be added up before done.

多謝觀賞

Mikusen

[ Last edited by Mikusen on 2006-8-26 at 10:32 PM ]

謝謝你
最喜愛以前的 Ferrari formula racing cars

用左 Finisher's Lummi-Red

After finishing clear coat and allow to dry for days, using compounds to rub on the body will make it shiny.

Below this is one of my example for your reference. But of course, there are different ways to make it shiny.

http://www.hkml.net/Discuz/viewt ... ghlight=&page=1

謝謝各位大大的意見

[常用溝油比例]
混合比例, GP2 主濟: 硬化濟 = 2:1,
混合後加入 40-50% thinner

當然每個步驟都好重要

其實自家都未用玩過 GP1
只知道 GP1 既主濟/硬化濟 比例 同 GP2 不同
可能係兩隻不同效果既光油
聽聞有用家試過 GP1
不過, GP2 既光澤 比 GP1 好

正所謂 "每個模型人背後的故事"


通常自家都會做一個測試, 用星星調色棒沾上少許 GP2 混合物,
然後放在斜面上, 看看會否太杰 / 太希, 適中便可
平時常用 0.3mm 噴筆, 都未試過塞槍

[ Last edited by Mikusen on 2006-8-21 at 01:25 PM ]

謝謝你

GP2 係一種 Urethane 油, 類似真車用光油

有冇 sample 睇睇先

不敢當
只係交流一下吧

好像 430 spider option 條軨

good good good

試試看 旺角皆旺商場 或 廣華街仁安

[ Last edited by Mikusen on 2006-8-21 at 05:32 PM ]

"未完的合照"
just a little progress tonight

唔使客氣

[ Last edited by Mikusen on 2006-8-22 at 10:25 AM ]

some more update today

1. The fast-open-lock were replaced by optional PE parts.


The one on the right hand-side is from original Fujimi kit. I have spent almost an hour to build the 4 locks.

Finally done


The engine top was covered by CF decals.




謝謝觀賞

其實係小弟 04年既作品, 不過仲有好多要改善既地方
製作車門部份, 自家這台 9LM 是不可動的.

[ Last edited by Mikusen on 2006-8-27 at 08:40 AM ]