Hi Again,

My Brumbar Late.  I hope you like.











QF

我懷疑 QF 兄既作品是否有於各大模型雜誌刊出? 因為質素實在超班. 工具細節豐富, 自製防磁紋很到位, 用色亦很有個人風格, 就連射擊孔塞栓也做成開啟狀態. 想問有否進行任何改裝? 可否簡單講解一下製作過程?
個人覺得唯一可挑剔是車身下部色彩及舊化過於單調, 令觀感上有 [上重下輕] 之感; 如將車身下部顏色調暗, 或加強下半部陰影和舊化效果, 不知會否好些?
少少意見, 多多得罪, 切莫見怪!

Joe

我都覺得呢張相有d問題,
或者影多幾張post上來睇下

Joe_Lo 兄是明眼人!  

The bottom chassis is left with minimum weathering for 情景 reason.  I built this 2 weeks ago and I still have not decdie the situation of the 情景.  The Brummbar is usually for street fighting so I need to match the weathering to the debris color.

kwonghyk兄

Next time I will post some photos of in progress pictures.  小弟 sometime lazy and not taking photos

Just a quick description:  The zim on the turret is aftermarket, only the chassis part of the zim is done by me to match the turret with tamiya putty.  The sideskirts are made by plastic for PE are too thin for that scale.

跟您交流模型心得好過癮啊!

QF

睇左 Quietfart 兄幾件作品, 每件水準都十分高, 大開眼界!!!

另近期亦多見不少 afv 高手出現, 真係可喜可賀~~~

實在太令人期待了.

另外亦都期待 qf 兄的情境完成品

x2 正未能預測的生化襲擊(毒)即將爆發 , 請大家做足防毒措施   如防毒(火)牆

我心諗以 QF 兄這樣高手沒理由看不到車身下半部的問題, 原來是 [好戲在後頭] , 熱切期待你的情景面世!  

另外你說防磁紋是 aftermarket 產品, 請問是否 Cavalier Model Production 出品的防磁紋還是整個車頂是 Resin cast? y產品質素如何?

[ Last edited by Joe_Lo on 2006-10-2 at 03:32 AM ]

Joe Lo 兄,

The the zim is from the old Jaugar.  It's very thick and I think it's little out of scale.   The zim itself is a bit strange too.   Cavaliar pattern does not match to it.

I usually prefer Cavalier because its easy to use and save alot of time.  But sometimes if you build 2 same type of tank at the same time, the zim would look identical.

Have you tried the Cav zim yet?

QF

QF 兄,

Cavalier 既 zim 我之前亦有用過, 你可以參考以下 link, 裡面架坦克防磁紋就用上此產品. 個人覺得產品質素一流, 比例正確, 雕刻細緻!

http://www.hkml.net/Discuz/viewt ... highlight=%2Bjoe_lo

另外想問問你有無用過之前 Armour Modelling 隨書附送兩支製作防磁紋工具?

[ Last edited by Joe_Lo on 2006-10-2 at 07:48 PM ]

Joe_Lo兄,

I always want one but I can not get one here in U.S.  What I use right now is just  Tamiya's PE zim too and regular toothpick  

QF

咁你要快 d 上網買翻 set, 我用過真係好好用, 又方便, 做出來既防磁紋又靚, 不過記住要用 d 凡士林 (Vaseline) 塗在工具上先做防磁紋, 咁就唔會同 d putty 痴住. 以前我都係用 Tamiya's PE zim tools, 依家有左佢就無用.
你話用 regular toothpick   牙籤   點用?

Joe_Lo兄,

Tooth pick is okay   The trick is to thin the putty so the point dont lift the putty off the model.  I get a box of tooth pick and as soon as the toothpick get dirty, I change a new one.  The advantage using a tooth pick is you have a good control of the direction of your zim.  You also are able to make it so its not too uniformed.  The disadvantage of toothpick is very time consuming and it is really not for beginner.  Give a try sometimes, you will be amazed you can get into hard to reach places!

I hope this help.

QF

要花咁多時間