米高兄、我通常会噴一層薄Ｍｒ．Ｓｕｒｆａｃｅ後再噴Soft 99 primer、無問題的。


Ｐｏｗｅｒ兄、９９係真車油来、噴完10－14日後基本就不再收縮。


雜果兄、今次係快Ｏｎｌｙ。


Ｌｅｏ兄、不用客気。

GOOD JOB~ 只係覺得座椅好似螢光左少少

糊兄、架車係送比人、我有Ｄ求求其其架（家得番支ＴＳ８紅色、再噴消光就算）。不過発現原来街車的油漆比Ｄｅｃａｌ車Ｈａｎｄｅｌ容易好多。

其實.....Soft99灰直接噴落injection kit係無問題....
噴完Surfacer先再噴Soft99灰, 第一係多做o左一個工序,
第二就係失去o左你噴Soft99灰o既原有意義

actually since our first gathering years ago, when you guys talked about the thinness of the paint layer, i have started to do the paint layer as thin as possible.
this would greatly help the presentation of the overall model

the smaller the scale, the thinner the layer that would well present the layout.

this is the one of the major influences that your guys has brought to me~~

I tried this before on my Enzo and I could not find any problem with it too.
Until the 2nd time, I tried it out again on my second attempt of building a red enzo and I find it shrink on those cut area.
May be I have sprayed the Soft 99 primer too thick on the body and once it dried, it shrink too much last time.

[ 本帖最後由 Mikusen 於 2007-10-11 03:46 PM 編輯 ]

Ｃａｓ兄、係個人習慣而己、我感覚上比較安心就造多一層Ｓｕｒｆａｃｅ、各人有不同造法、好似你地用ＧＰ２　Ｏ甘、　你同ＤＭ的手法都有分別一様　Ｏ甘　Ｌａｗ．

都要你肯聽肯學先得o既

其實任何一隻灰都會收縮,噴得越厚就收縮得越多, 我覺得問題不在於soft99度囉..

好靚..... @@
自問冇可能有咁好技術 @@

各施各法, 砌得件模型靚靚就係好方法, 呢點我明白.
我只係想帶出一點, Soff99底灰係可以直接噴上injection plastic kit上面而不一定要先噴其他油/灰.

真係三個字形容度:快，靚，正 得閒砌多d街車

As I have mentioned, the problem I experienced before is Soft 99 attacked those "切件位", just like being ate-up. I wonder if someone experienced similar case.
But in fact, I have no problem with my black enzo with soft 99 primer

[ 本帖最後由 Mikusen 於 2007-10-11 09:50 PM 編輯 ]

I agree
but still some cases is not that perfect.

[ 本帖最後由 Mikusen 於 2007-10-12 01:55 AM 編輯 ]

Skyline兄、我無セ技術架、造多幾次就得、有セ問題的話就話我知、我一安Ｓｈａｒｅ我所知。

謝謝Ｔｏｍｍｙ兄、我以後都会試下製作多Ｄ街車。

Ｃａｓ兄、謝謝有関Soff99底灰的分享。